de     

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Last revisionBoth sides next revision
en:ztex_boards:ztex_fpga_boards:usb_powering [2016/09/15 08:33] stefanen:ztex_boards:ztex_fpga_boards:usb_powering [2016/11/24 23:31] stefan
Line 3: Line 3:
  
 Whether / how USB powering is supported is listed in the following table Whether / how USB powering is supported is listed in the following table
-^ FPGA Board  ^ Power source selection ^ comments + FPGA Board  ^ Power source selection ^ comments 
-| [[http://www.ztex.de/usb-fpga-2/usb-fpga-2.16.e.html|USB-FPGA Module 2.16]]  |  no  | USB powering not supported + [[http://www.ztex.de/usb-fpga-2/usb-fpga-2.18.e.html|USB-FPGA Module 2.18]]  |  no  | USB powering not supported 
-| [[http://www.ztex.de/usb-fpga-2/usb-fpga-2.14.e.html|USB-FPGA Module 2.14]]  |  automatically  | USB 3.0 delivers sufficient power for small applications including RAM  | +|  [[http://www.ztex.de/usb-fpga-2/usb-fpga-2.16.e.html|USB-FPGA Module 2.16]]  |  no  | USB powering not supported 
-| [[http://www.ztex.de/usb-fpga-2/usb-fpga-2.13.e.html|USB-FPGA Module 2.13]]  |  by soldering a 0Ω  | not recommended because USB 2.0 usually deliver insufficient power  | + [[http://www.ztex.de/usb-fpga-2/usb-fpga-2.14.e.html|USB-FPGA Module 2.14]]  |  automatically  | USB 3.0 delivers sufficient power for small applications including RAM  | 
-| [[http://www.ztex.de/usb-fpga-2/usb-fpga-2.04.e.html|USB-FPGA Module 2.04]]  |  by soldering a 0Ω  | USB 2.0 usually deliver insufficient power if RAM is used  | + [[http://www.ztex.de/usb-fpga-2/usb-fpga-2.13.e.html|USB-FPGA Module 2.13]]  |  by soldering a 0Ω resistor  | not recommended because USB 2.0 usually deliver insufficient power  | 
-| [[http://www.ztex.de/usb-fpga-2/usb-fpga-2.01.e.html|USB-FPGA Module 2.01]]  |  by jumper  | USB 2.0 usually deliver sufficient power |+ [[http://www.ztex.de/usb-fpga-2/usb-fpga-2.04.e.html|USB-FPGA Module 2.04]]  |  by soldering a 0Ω resistor | USB 2.0 usually deliver insufficient power if RAM is used  | 
 + [[http://www.ztex.de/usb-fpga-2/usb-fpga-2.01.e.html|USB-FPGA Module 2.01]]  |  by jumper  | USB 2.0 usually deliver sufficient power |
  
  
 
en/ztex_boards/ztex_fpga_boards/usb_powering.txt · Last modified: 2023/10/30 16:18 by stefan
 
Recent changes RSS feed Creative Commons License Powered by PHP Debian Driven by DokuWiki
[ZTEX Home] [Imprint] [Privacy policy]