This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
en:discussions:device_overheating_message [2013/06/11 16:40] – [Device overheating message] 178.24.145.101 | en:discussions:device_overheating_message [2017/02/04 19:12] (current) – gelöscht stefan | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | <- [[: | ||
- | |||
- | ====== Device overheating message ====== | ||
- | |||
- | //, 2013/06/11 09:46 // | ||
- | |||
- | Hi, I'm running my FPGA 1.15b + experimental board 1.3 on Linux. | ||
- | |||
- | I was able to upload the firmware to eeprom with the following command: | ||
- | |||
- | vp@deathstar: | ||
- | Firmware to EEPROM upload time: 2581 ms | ||
- | |||
- | the ihx i've got from btcminer, because I wasn't able to find it in the Download package offered in the download area. if its there, please advise me. The .bit file i couldnt find it as well. do I MUST to generate the bitstream or do you have it download? | ||
- | |||
- | then I tried to run it as: | ||
- | |||
- | java -cp ~/ | ||
- | |||
- | ztex_ufm1_15b1-04A39E20AD: | ||
- | ztex_ufm1_15b1-04A39E20AD: | ||
- | |||
- | Warning: Possible Bitstream CRC error: INIT_B_HIST=111 | ||
- | | ||
- | ztex_ufm1_15b1-04A39E20AD: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | |||
- | |||
- | then after that It just quits with the message: | ||
- | |||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | |||
- | if i set the BTCMiner parameter -oh to 1.0 I don't get the CRC error but the frequency goes down like: | ||
- | |||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | ztex_ufm1_15b1-04A39E20AD-1: | ||
- | |||
- | |||
- | |||
- | What are the possible causes? As power supply I'm using this one from Conrad http:// | ||
- | |||
- | ~~DISCUSSION~~ | ||