Differences

This shows you the differences between two versions of the page.

--- en:software:fwloader [2016/08/21 09:22] – [Global options] stefan
+++ en:software:fwloader [2017/03/22 21:35] – [Ordered options] stefan
@@ Line 12: / Line 12: @@
 At start-up ''FWLoader'' scans for compatible devices. By default it searches for devices
 with ZTEX vendor and product ID. Other device classes can be specified by the options
-''-c'' (scans for unconfigured EZ-USB devices), ''-v'' (devices with ZTEX firmware but non-standard vendor and prduct ID)
+''-c'' (scans for unconfigured EZ-USB devices) and ''-v'' (devices with ZTEX firmware but non-standard vendor and prduct ID).
-and ''-vc'' (devices with ZTEX firmware and Cypress vendor and product ID).
 A list of devices can by printed using ''-p''. The device which shall be configured is specified by ''-d''.
@@ Line 25: / Line 24: @@
 |-c               | Scan for Cypress EZ-USB devices without ZTEX firmware |
 |-v <VID> <PID>   | Scan for devices with the given Vendor ID and Product ID |
+|-vc              | Equal to -v 0x4b4 0x8613 |
 |-s <sn string>   | Only scan for devices with that serial number |
 |-d <number>      | Device index (default: 0, use -p to get a list) |
@@ Line 34: / Line 34: @@
 ^ Option ^ Description ^
 | -i              | Print device info |
+| -ru             | Reset EZ-USB |
+| -uu <ihx file>  | Upload Firmware to EZ-USB |
+|  The following options require an installed ZTEX Firmware (e.g. by ''-uu <firmware>'')  ||
 | -ii             | Print device info + capabilities |
 | -if             | Print FPGA state |
 | -ic             | Print configuration data and flash info |
-| -ss <sn string> | Set the serial number, see [[#serial_numbers]] |
+| -il             | Print log messages of FX3 based FPGA Boards |
-| -ru             | Reset EZ-USB Microcontroller |
+| -re             | Disable EZ-USB firmware in nonvolatile memory |
-| -uu <ihx file>  | Upload EZ-USB Firmware |
+| -ue <ihx file>  | Upload EZ-USB Firmware to nonvolatile memory |
-| -bs 0<nowiki>|</nowiki>1<nowiki>|</nowiki>A       | Bit swapping for bitstreams: 0: disable, 1: enable, A: automatic detection |
+| -ss <sn string>  | Set the serial number, see [[#serial_numbers]] |
-|  The following options require an installed ZTEX Firmware (e.g. by ''-uu <firmware>'')  ||
+| -su <VID> <PID>  | Set the USB ID's in configuration memory, 0 to load ID's defined by firmware |
+| -sp <string>    | Set the product string in configuration memory, empty string to load firmware default |
+| -sf <number>    | Select FPGA (default: 0) |
 | -rf             | Reset FPGA |
 | -uf <bitstream> | Upload bitstream to FPGA |
-| -sf <number>    | Select FPGA (default: 0) |
-| -re             | Disable EZ-USB firmware in EEPROM |
-| -ue <ihx file>  | Upload EZ-USB Firmware to EEPROM |
-| -rm             | Disable bitstream in Flash |
 | -um <bitstream> | Upload bitstream to Flash |
+| -rm             | Disable bitstream in Flash |
+| -bs 0<nowiki>|</nowiki>1<nowiki>|</nowiki>A       | Bit swapping for bitstreams: 0: disable, 1: enable, A: automatic detection |
 | -uxf <ihx file> | Upload Firmware / data  to ATxmega Flash |
 | -uxe <ihx file> | Upload data to ATxmega EEPROM |